Wedge Planing Stop

A bench jig of paired wedges that grips a workpiece by friction and releases with a tap.

2 takes from different creators

Hot Take: Why the Viral Four-Wedge Planing Stop Only Needs One Wedge

A single wedge with a block glued to its tip pins a board against a fixed strip and tightens itself as you plane, which is what the viral version uses two loose wedges to do. Keeping the strip narrow also keeps the work in close rather than at arm's length.

hold a board for edge planing, workholding without clamps, planing stop jig, grip thin stock on the bench, traditional bench appliance

intermediate Tools: hand planer Added Nov 7, 2026

The Problem

When planing a thin board, it's hard to clamp it to your workbench. The jig that solves it has been circulating lately as four wedges — two glued to the bench, two loose inside them, joined with a strip of elastic or webbing — and it does work.

This creator's objection to that version is the part count and where it leaves the work: "it's actually totally stupid," and "it's terrible for your body. You need to be planing in close, not all the way out here."

What the Older Version Does Differently

Three pieces instead of four, and one of them slides.

  • A narrow fixed strip to plane against. Narrow is the part that matters: it holds the work near the front edge of the bench, where you plane with your arms in rather than extended.
  • One sliding wedge, where the viral version uses two.
  • A small block glued across the thin tip of that wedge. The block catches the end of the board, so the single wedge both tapers and hooks — which is the job the second loose wedge was doing. It grips any width of stock without being sized to it.

In use, the board goes against the strip and the wedge pushes up behind it. Planing away from you drives the wedge home; a tap backwards releases the work.

Pro tip: He gives no sizes, so treat the three pieces as proportions rather than a cut list: the wedge taper wants to be shallow enough to hold by friction, and the block only has to stand proud of the wedge by less than your thinnest stock, or the plane will hit it. Set the wedge so the cutting stroke tightens it — fitted the other way round, every pass loosens the work.
Pro tip: This is not a new design. He points out that the single-wedge version has been in trade manuals and journals for about a century, and that the four-wedge one is a recent reinvention of it.

Grip Small Workpieces for Planing Between Two Pairs of Wedges

Two fixed wedges glued to the bench and two loose wedges inside them make a stop that holds a workpiece by friction alone. Planing away from you drives the wedges tighter; a tap back toward you releases the work.

workholding for small parts, hold thin boards without clamps, bench stop for hand planing

intermediate Tools: hand planer, wood glue Added Jul 29, 2026

The Problem

A small or thin workpiece has nothing to clamp. A vice grips it at one end and it chatters at the other. A bench dog holds it against a push but lets it skew. Clamps hold it well and sit exactly where the plane needs to go, so you spend the session moving them.

The Technique

The jig is four wedges and a strip of webbing, and it holds work by friction with nothing to tighten.

  1. Cut two wedges and glue them to the benchtop in a shallow V, with the opening facing you and the narrow end away from you. The gap between them at the narrow end should be a little less than the width of the work you plane most.
  2. Cut two more wedges, thinner than the first pair, with the same taper.
  3. Join the thin pair at their wide ends with a short strip of webbing, leaving a gap between them. The webbing keeps them together as one unit and stops them dropping off the bench when the work comes out.
  4. Drop the thin pair inside the fixed pair, tapers matching.
  5. Slide the workpiece into the pocket between the two thin wedges and push it away from you until it snugs.

Plane away from yourself. Each stroke pushes the work deeper into the taper, which drives the thin wedges outward against the fixed ones and tightens the grip.

To release, tap the workpiece back toward you. The wedges slacken and the work lifts straight out.

Pro tip: Make the thin inner wedges from a wood softer than the work — poplar or pine against oak. The inner wedges are the wear part and they're the two-minute piece to replace, while the fixed pair stays glued down.

DIYsolvr helps you find the best DIY videos. Browse all 609 techniques